Office Chair Backrest Weaving

There are mainly three methods for office chair backrest weaving: boss chair cushion weaving, creative ball-thread weaving for heart-shaped chair backrests, and plastic rattan chair backrest weaving. Details are as follows:

Boss Chair Cushion Weaving: For materials, you will need eight skeins of thread and two liang (a traditional Chinese unit of weight, approximately 100 grams) of combined thread. The width should be about fifty centimeters, with forty stitches for casting on. The length can be adjusted according to actual needs. When finishing, reserve two meters of thread for sewing. Additionally, reserve at least ten or twelve meters of thread before starting to weave. The method for casting on involves taking a thread from the middle and using both hands to cast on stitches. The more stitches, the more pairs of hands are needed, and a circular needle can be used. Specifically, after holding the needle in your right hand, use your index finger and thumb to pass downward through the middle, then loop upward. The needle in your left hand should come up from below your thumb and then pass downward from above your index finger. Release your thumb and pull the thread, being careful not to make it too tight. Repeat this process to complete casting on.

Creative Ball-Thread Weaving for Heart-Shaped Chair Backrests: After dividing the stitches, continue learning the weaving on the other side by threading the part on the rope back onto the knitting needle. Take out the yellow thread, cut off the first ball, reserve a long thread end, and tie a knot with the thread end on the left side, leaving half the length of the thread. Start weaving with the blue thread from the right side, weaving each segment of the first stitch only once, and from the second stitch onward, weave two stitches per segment until all the loops on the left knitting needle are finished. On the second row, reverse direction and weave with the yellow thread, skipping the first stitch, and from the second and third stitches onward, weave two stitches per segment until the last stitch is finished, leaving half the length of the thread. On the third row, switch to the blue thread and start decreasing stitches on the inside. From the second stitch onward, weave two stitches per segment until only the last two stitches remain, then combine the last two stitches into one to decrease one stitch, leaving half the length of the blue thread. Then reverse direction and weave the fourth row with the yellow thread, which should always be woven without increasing or decreasing stitches, starting directly from the first stitch and weaving two stitches per segment from the second stitch onward. On the fifth row, continue decreasing stitches on the inside, combining the first two stitches into one to decrease one stitch, and from the second stitch onward, weave two stitches per segment, and from the third stitch onward, weave two stitches per segment. Starting from the seventh row, decrease stitches on both sides, combining the first two stitches into one to decrease one stitch, then switch to the yellow thread. On the eighth row, weave half a segment of the thread for the first stitch. On the ninth row, combine the first two stitches into one to decrease one stitch, and from the second stitch onward, weave two stitches per segment until only the last two stitches remain, then combine the last two stitches into one to decrease one stitch. On the tenth row, weave two stitches per segment from the first stitch onward until all the loops on the left knitting needle are finished. On the eleventh row, combine two stitches into one to decrease one stitch, and from the third stitch onward, weave two stitches per segment. On the twelfth row, perform the final finishing by combining two stitches into one and weaving one stitch per segment, then combining two stitches into one again to decrease one stitch, continuing until only one stitch remains. Slip it back onto the left knitting needle, cut the thread from the root of the ball, pick out the thread end, pull it tight to complete the finishing, pull tight and cut the other thread end, and hide all the thread ends.

Plastic Rattan Chair Backrest Weaving: The seat and backrest can be woven together or separately, depending on actual needs and design.